How to install cork flooring on Stairs (Bull Nose)

how to install cork flooring in stairs

 

1. Check with local building codes to ensure the project conforms to building and safety regulations (ie. Flush stair nosing vs. overlapping or “Bull nosing”).

2. The tread of the stair is not allowed to move. This means your floating flooring must be anchored to the stair tread (using glue/adhesive, staples, nails or screws).

3. Inspect your stair treads. They must be sound (no rot or cracked boards, no holes or gaps in the tread), flat (not on a slant), no visible wear pattern on the tread and must be clean (no paint, old adhesives, etc) to allow for full adhesion.

4. To begin installation you must finish the flooring up to the bottom of your staircase while still maintaining the expansion gap up to the base of the first stair.

5. When installing your flooring on the stairs, you will not require underlayment nor poly sheeting (if being used underneath your flooring). You will not need to account for expansion of your flooring on the tread as you will be gluing your flooring directly to the tread (the floor will not be able to expand, therefore it does not require an expansion gap).

6. You will need to “square off” the tread overlap of your stair. You can do this in two ways: 1) You can cut or trim the tread to lay flush with your rise, or 2) you can “fill in the gap” by applying your flooring to the rise (thus it becomes “the riser”). This description involves attaching flooring to the rise (filling in the gap instead of trimming off the edge ). stairs Installation with cork flooring

You will always install the riser (the vertical surface of the stair) before you install the tread. And always remember to cut off the “tongue and groove” of your cork flooring prior to measuring the plank. If your measurements require more than one plank to complete a tread or riser (especially true if you are using a bevelled edge or narrow plank installation), then you will be required to assemble enough flooring planks to accomplish the amount of square footage.

7. Measure from the floor to the top of the riser (the level of the tread).

8. Cut a piece of flooring to match the height of your riser (always remove tongue and glove before cutting a plank to match your measurements).bull nose cork flooring stairs installing Liberally apply the commercial glue to the back of the plank(s) and press the flooring in place against the rise.

9. Measure your tread – remember to allow for the stair nosing. Subtract the measurement of the nosing from the tread depth and cut plank(s) to the adjusted measurement.

10. Apply glue to back of flooring (same application as for the riser) and press firmly into place on the tread of the stair. Installation cork stairsEnsure that the front of the stair has been left with a gap that is appropriate for the size of the nosing.

11. To install the stair nosing, measure the length of your tread (and the length of all the treads) and cut your nosing to fit – remember to number your nosing if the lengths differ from one tread to another!

12. Apply the adhesive to the back of the nosing (only applying glue to the surface area that will come in direct contact with the stair tread, not the flooring) and press firmly into place. Install bull nose cork flooring

13. Pre-drill pilot holes in the stair nosing (not the flooring) every 8-10 inches (20-25cm). Hammer in the nails (or screw down the screws) into the pilot holes (making sure the nails or screws are flush or counter sunk below the surface of the nosing) to ensure the nosing is anchored to the stair surface. cork flooring stairs

14. Continue finishing each stair in the same manner (riser first, tread second, stair nosing third) until you reach the top of the stairs or to the first landing.

15. When installing on a landing/top of the stairs, you will return to a “floating floor” installation method. You will not anchor the flooring in place, but you will still need to anchor (glue and nail/screw down) the nosing. Measure the size of the landing (minus the nosing edge and the 1/2inch expansion gap) and install underlayment and/or poly sheeting (if used in the regular flooring install). cork flooring stairs with wood nosing

16. To ensure you leave enough space for the nosing, you will be required to mark a “starting point”. Using a scrap piece of nosing, place the nosing over the edge of the stair/landing. Make a mark where the nosing edge (the edge that is in contact with the stair/landing’s surface) meets the flooring. This is your “Starting point”.

install stairs with cork flooring

Keyword How to install cork flooring,in reviews in installati plank in pros and cons durability tiles a floor for board for planks, discount cheap a plank cost glue down prices for kitchens in bathroom in basement in best cost of colors lay evora pros and cons hard vinyl hard floors for basement, bamboo basement linoleum for plank rubber bamboo sale white laminate, How to install cork flooring installati options colored installing hard discount wicanders reviews what is natural parquet slate where buy clean buy options of floating basement floor benefits of in ideas. cheap durability of rubber much is and dogs hard linoleum for marmoleum ceramic tile in types of hard wood underlayment cheap lay samples, How to install cork flooring ceramic installati ,review pictures commercial dark for sale laminate cleaning wall outdoor is waterproof ceramic marmoleum lay tile options hard pictures of resilient lay for basements bathroom is durable a discount a capri snap together images stair treads ideas a hard manufacturers. floating in is good wall panels click durable, is porcelain a ceramic vinyl sheet liquidators garage express lay grey diy diy best and dogs sheets options, How to install cork flooring installing bamboo natural floors cost gray types of engineered hard price lay ceramic hard installati ikea discount linoleum tiles easy clean black laminate for concrete globus tile underlayment roll stone expanko we home capri .

Other iCork Website by iCork Floor LLC